We have all the equipment and parts to work on the BRC Plug&Drive systems. Both the parts and complete systems are available from stock.
Does your BRC system need maintenance or repair? Contact us for an appointment with us or at a dealer in your area.
The Sequent Plug&Drive system is one of the most recent developments of the company BRC. This system was created based on the knowledge of the previous Sequent systems, but has a number of extra possibilities.
The system consists of the evaporator (Genius), the BRC injectors, the pressure and temperature sensor, the injector rail, and the control unit.
Compared to the previous systems, the main innovation can be found in the ECU (computer). The steering unit can communicate with the car’s OBD system. This was not possible with the previous systems. This allows for better integration with the vehicle’s petrol system.
Spare parts BRC Plug&Drive
Plug&Drive Control Unit
– Microprocessor 16 bit 40 MHz
– Resistant to following temperatures: -40°C + 105°C
– Waterproof
– Manufactured according to vehicle standards (in terms of protections and input and output signals)
– Operating voltage: 8 V ÷ 16 V
– Compatibility of the sensors and actuators with EOBD
– Communication and reprogramming with the PC via K-line
– KWP2000 communication protocol is supported
– CAN 2.0 communication is supported
– Can control up to 8 injectors
– Integrated injection interruption and emulation (so no separate module is required for this)
– Approvals: R67-01 – R110 – 2004/104/CE
The BRC-Injector
Impedance: 2.04 Ω / 2.35 mH at 20 °C
Resistant to temperatures between -40 °C and 120 °C (during use)
Voltage: 6 V ÷ 16 V
Approvals: R67-01; R110.
There are a total of 4 types of injectors, which are used depending on the power of the vehicle. The table below shows a distinction according to the power and the evaporator used.
| Types of injectors | LPG Evaporator Genius MB800 | LPG Evaporator MB1200 | LPG evaporator MB1500 | LPG Evaporator Genius MAX | |
| Normal Type | Aspiring | 17 kW/cyl. | 21 kW/cyl. | 23 kW/cyl. | – |
| Supercharged | 22 kW/cyl. | 26 kW/cyl. | 28 kW/cyl. | – | |
| Max Type | Aspiring | – | 26 kW/cyl. | 30 kW/cyl. | 30 kW/cyl. |
| Supercharged | – | 32 kW/cyl. | 36 kW/cyl. | 36 kW/cyl. | |
| Super Max Type | Aspiring | -35 kW/cyl. | 35 kW/cyl. | ||
| Supercharged | -42 kW/cyl. | 42 kW/cyl. |
PTS SENSOR for BRC Plug&Drive
This sensor measures both the gas pressure and the temperature.
– Weight: 22 grams
– Dimensions: ø= 24 mm, h= 64,5 mm
– An integrated connector is provided on the sensor
– The sensor can be used at temperatures between -30 °C and 130 °C.
– This sensor is homologated with both 67R-01 and R110.
Map sensor (manifoild pressure sensor)
This sensor weighs only 17 grams and has the following dimensions: diamger 33 mm, height 63 mm (including pipe). The sensor is suitable for measuring pressures between 0 and 2.5 bar, with a precision of 1.5% F.S. The output voltage is between 0 and 5 Volts.
BRC filter
With the Plug&Drive system, this filter is supplied for installation in the gaseous phase. The cartridge in this filter must be replaced in time, so that the injectors are protected against any dirt that is in the gas.
Both the complete filters and the cartridges are available from stock. Lpg filter replacement? We do it immediately for you with us in Eeklo without an appointment.
Switch
This round switch is operated with 1 push button, to switch between the petrol and the gas phase. In the switch is mounted a “buzzer”, which makes a sound when the tank is empty.
Four green LEDs indicate the tank capacity, and one red/green LED indicates whether you are driving on gas or petrol.
Evaporator BRC Genius MB
This 1-stage evaporator is available in 3 versions: MB800 (80 kPa pressure), MB1200 (120 kPa pressure) or MB1500 (150 kPa pressure). The largest evaporator of this type delivers a power of up to 160 kW (this is the type MB1500).
This evaporator has an R67-01 approval.
Evaporator BRC Genius MAX
This is also a 1-stage evaporator, but can have a power of up to 240 kW (with pressure 150 kPa). The evaporator also has an R67-01 approval.